Outdoor Enclosures and Cabinets
Type of Enclosures:
Batteries Enclosures for commercial, industrial, military applications, battery
enclosures, battery cabinets, cabinets, battery cabinets, batteries enclosures,
batteries cabinets, enclosures, Enclosures commercial, enclosures industrial,
enclosures data and telecommunication technology applications, Outdoor Cabinets
for Communications equipment, outdoor cabinets, cabinets, enclosures battery
cabinets, battery enclosures, communications cabins, communications enclosures
|
OkSolar.com Affiliate
|
The OK30 is the superior design in communication cabinets, being as rigid
as steel & yet noticeably lighter than the old heavy steel constructed
cabinets. This is made possible with o ur
own aluminum recipe called ALUMIFLEX. The SPDC ODD-30 offers the
protection needed for any sever outdoor environment. The
SPDC ODD-30 is constructed of .125 ALUMIFLEX material, & comes
with an additional .125 ALUMISHIELD top cover, thereby fully protecting
your equipment from falling ice and the sun's heat penetration. Ultimate
security is provided by a three point locking system, which utilizes a
NEMA stainless steel cabinets, the
SPDC ODD-30, made of ALIMIFLEX, will operate without affecting or
being effected by RF influences. Outdoor cabinets are becoming the
alternative shelter solution for today's complicated zoning
requirements. So weather your installing a new shelter or adding room to
your existing one, the OK-30 is the
ultimate solution.
|
GENERAL |
Weight:
80 lbs. assembled
120 Lbs. Shipping weight |
Doors:
Two - secured by three point locking system
Locks via customer supplied padlocks
sealed with 13/16" aluminum filled gaskets |
Material:
.125 ALUMIFLEX
Finish: Flat aluminum
RF properties: Non-ferrous |
Vents:
Twelve bottom louvers per door
Six top louvers - in top cover under ALUMISHIELD
One removable filter panel per door
Six fixed filter pads in top cover |
| Handles:
Stainless steel |
| Exterior Screws:
Stainless with NEMA washers & nylon locking nuts |
|
RACKING SPECIFICATIONS |
Rails:
Two standard (For additional rails see accessories)
Alodine coated
Holes tapped to 10 x 32 threads
Each rail supported by three R-STRUTS
.125 material (ALUMIFLEX) |
| Spacing:
19" EIA STANDARD |
| Positioning:
All rails fully adjustable from front to rear |
| Useable Height:
30 inches |
Useable Depth:
Maximum: 21 1/2" Minimum: 19 3/4" (See below)
| |
*Section Starting & Ending Points |
Vertical Height Per section |
Effective Depth For Each Section |
| Top |
26.75" - 30.00" = |
3.25" |
21 1/2" |
| |
26.57" - 26.75" = |
.18" |
20 1/2" |
| |
21.00" - 26.57" = |
5.57" |
21 1/2" |
| Center |
9.00" - 21.00" = |
12.00" |
19 3/4" |
| |
3.43" - 9.00" = |
5.57" |
21 1/2" |
| |
3.25" - 3.43" = |
.18" |
20 1/2" |
| Bottom |
0.00" - 3.25" = |
3.25" |
21 1/2 |
*Section measurements start from the bottom of the cabinet (0.00")
& runs vertically upward towards the top of the cabinet (30.00"):
|
|
DOOR OPENING CLEARANCE |
| Width :
19 1/2 inches |
| Height :
25 13/16 inches |
|
EXTERIOR CABINET DIMENSIONS |
Main Body:
Width: 25 1/2 inches
Height: 30 1/4 inches
Depth: 25 1/4 inches |
Alumishield:
Width: 28 1/16 inches
Hang down height: 1 3/4 inches
Depth: 29 inches |
Handles:
Handles: Protrude 1 7/8 inches |
Total Space Occupied:
Width: 28 1/16 inches
Height: 30 1/2 inches
Depth: 29 inches |
|
INSIDE CLEARANCE - LESS RAILS |
| Width:
23 5/8 inches |
| Height:
30 inches |
| Depth:
See racking spec's - useable depth chart above |
|
RATINGS |
NEMA: CLASS: 250
TYPE: 4
|
|
WARRANTY |
| Period: Two Years -
Unconditional |
|
ACCESSORIES
|
| R-2-30: Two extra 30"
rails & mtg. hardware |
| MTDX: Mounting tray |
| CA-4: Caster Kit (4) &
mtg. hardware |
| SCR-432: Rail Screws (4)
10x32 |
|
OPTIONS
|
| P-DX: Powder baked on
textured paint |
Paint Tested: 500 Hour
salt spray
500 hour immersion |
|
SHIPPING INFORMATION |
The SP ODD-30DX is shipped fully assembled, but can be
easily
knocked down and re-assembled at your site, if desired |
|
Applications:
|
