Outdoor Enclosures and Cabinets
Type of Enclosures:
Batteries Enclosures for commercial, industrial, military applications, battery
enclosures, battery cabinets, cabinets, battery cabinets, batteries enclosures,
batteries cabinets, enclosures, Enclosures commercial, enclosures industrial,
enclosures data and telecommunication technology applications, Outdoor Cabinets
for Communications equipment, outdoor cabinets, cabinets, enclosures battery
cabinets, battery enclosures, communications cabins, communications enclosures
|
OkSolar.com Affiliate
|
OUTDOOR DATA BOX 14" SQUARE SPDCWCU-B14
| SECURITY - |
Padlocking toplid
Padlocking rear I/O access door |
| CONSTRUCTED -
|
Out of .125 ALUMIFLEX Continuously
welded on all eight panel seams |
| THREE SECTIONS -
|
Weatherproof radio section
Vented Battery Section
Rear I/O wiring section |
| FINISH - |
Textured polyester powder baked on,
paint |
| I/O LINE
PROVISION - |
Rear section supports 48 connections
for I/O lines
Access provided through 1/2" conduit hole |
The construtcion and desighn of our WCU-B14 allows you to house your data
equipment in a tested enclosure, capable of providing more features than
most jobs require. The WCU-B14 was designed and tested, collecting on-site
data in the oilfields in Texas. Being constructed with tree separate
sections, the WCU-B14 supports all of today's basic collection
requirements and can be easily retrofitted into your existing data
operaton. These holes when used with our WCU-C (optional pole mounting
kit) will accomodate up to a two inch pole. A 3/4" hole is already drilled
into the top lid to allow your antenna to be mounted directly above your
TX-RX unit. Weighing only 21 Lbs., and being the most economical enclosure
of it's kind, the WCU-B14 is today's answer for data collection anywhere
on the globe.
|
GENERAL
|
| Weights:
21 lbs. |
| Material:
.125 ALUMIFLEX (our own aluminum recipe) RF properties: Non-ferrous |
Mounting:
Four 5/16" holes provided for wall mounting
Or the four holes may be used with our optional WCU-C (pole mt kit)
for mtg on, up to a 2" pole |
| Finish:
Grey, textured, powder baked on paint |
Top Lid & Rear Door:
Secured with a hasp locking system
Locks via customer supplied padlock
Sealed with aluminum filled gasket |
Vents:
Battery section: Has four vent louvers in bottom
Radio section: None
I/O section: None |
| Center divider wall
(Power feed thru): Has two 1/4" holes in the top of wall, which
provide access for two bolts and two rubber grommets. These allow your
battery + & - to be passed thru from the battery section to the radio
section |
|
EXTERIOR DIMENSIONS
|
Main Body:
Width: 14 3/4 inches
Height: 13 7/8 inches
Depth: 14 1/4 inches |
Top Lid:
Width: 15 1/8 inches
Height: 1 inch
Depth: 15 3/4 inches |
Top Lid Hasp:
Protrudes through door: 5/16" inch
Very tight fitting: Holds door closed against gasket |
Total Space Occupied:
Width: 15 1/8 inches
Height: 14 3/16 inches
Depth: 15 3/4 inches |
|
BATTERY USEABLE CLEARANCE
|
| Width:
14 inches |
| Height:
13 1/2 inches |
| Depth: 7
1/2 inches |
|
RADIO SECTION USEABLE CLEARANCE
|
| Width :
12 1/4 inches |
| Height :
13 1/2 inches |
| Depth :
5 5/8 inches |
|
RADIO SECTION
|
| Mounting Slot:
Width: 3/16" Length: 6 3/4" (cut out of floor) |
| Antenna hole:
3/4" holecut into top lid above radio section |
|
I/O SECTION WIRING SPACE
|
| Width :
3 7/8 inches |
| Height :
10 7/8 inches |
| Depth :
1 1/2 inches |
|
RATINGS
|
NEMA: CLASS: 250
TYPE: 3R |
Paint Tested: 500
Hour salt spray
500 Hour immersion |
|
WARRANTY
|
|
7 Years Unconditional |
|
SHIPPING INFORMATION
|
| The WCU-B14 is shipped via UPS |
|
Applications:
|
