Wireless Sensors, Sensor RF Identification, Wireless Receivers, Wireless Transmitters, Wireless Antennas

High value wireless solutions for the automation and communications industry

Sensor RF Identification 418 MHz. FCC Certified Radio Transmitter Main Features 64-Bit unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent pending Battery life up to 5 years Very small (1.4” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost Description: The Point Sensor RF Identification sensor is a battery operated, microprocessor controlled 418 MHz. FCC certified radio transmitter. The Point Sensor RF Identification sensor has an on board time of day clock that allows it to spend most of the time in a low power quiescent state. At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information is combined with a CRC-16 error check and transmitted in a very short data packet that results in a transmitter on time of only 15 milliseconds. This architecture allows the Point Sensor RF Identification sensor to consume very low energy resulting in a battery life of up to 5 years. The electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. An external magnet is used to activate the service switch. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). Start the Sensor by momentarily placing the magnet next to the transmitter. When the service switch is activated a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The service switch is also used to put the Sensor in a quiescent mode (no transmissions and very low power consumption). This is the state the Sensor is in when you receive it from the manufacturer. Activate the service switch for 5 seconds or more to enter this powered down state.

Technical Features:   PARAMETER UNITS Transmission rate 10-240 seconds (specify when ordering) Shelf life with battery installed 5 Years in quiescent mode Dimensions (enclosure) 1.4 W X 2.1 H X .6 D (inches) Weight 1.0 oz. Operating Temperature -40� to 85� C Battery life with transmissions 2-5 years with tx period of 10-240 seconds Battery 3.6 volt Lithium FCC Certified FCC ID: M5ZWOW

Wireless Receivers: A complete family of wireless RF sensors, transmitters, loggers, repeaters, receivers and servers spanning the 418MHz. to 2.4GHz frequency range. With an emphasis on modularity and compatibility, The Point Family is ideally suited for a broad range of applications from basic telemetry to custom engineered wireless networking solutions.

Wireless Sensors: Adott offers an expanded line of wireless sensors to measure temperature, relative humidity, pressure, vibration, analog voltage and current, and discrete digital inputs. Each sensor is battery operated and fitted with a microprocessor controlled 418 MHz radio transmitter.

IQUPS If you are a systems integrator, installer, engineering procurement contractor or an electrical contractor

We will work with you to design a Solar - Fuel Cell and or Wind power system for your project some applications Business - On-Grid Commercial Buildings and Off-Grid Industrial Remote electricity anytime anywhere!.

Businesses - Government Agencies and homeowners around the world are using OkSolar systems Integrated systems Solar, fuel Cells and wind energy.

Applications: Commercial - Industrial - Disaster Relief - Military and Residential AirportIQ UPS Airfield Power Backup Electrical

Communication infrastructure(Local and Federal Government)

Base Stations for Mobil Networks that can run on Solar, Wind and Fuel Cells.IQ UPS Base stations cut diesel usage by 75 percent. IQUPS.com has designed a base station for mobile networks that would run on sun, wind power and fuel cells. Gas Stations (Powering gasoline pumps during a power failure).

Hospital EMS: IQ UPS Hospital Power Backup Electrical ( Emergency Power Back-up for Hospitals ).

Rail Roads: Railroad crossing signals backup.

Traffic intersections: backup power for critical LED traffic light intersections.

Solar Trees Arrays We Delivered On-Site For Fast Plug and Pay Installation Solar Tree structure are designed for the following applications: Shading vehicles from the sun and at the same time generate Green energy. Facilitate the creation of infrastructure for electric vehicles.

Traffic Application: -Keeping Traffic Moving When The Power Goes Out Item#1608450 Portable Solar Powered 120 volts 60Hz. or 230 Volts 50 Hz, Portable Solar Powered 220 Volts 50 Hz, Portable Solar Powered 230V 50Hz, Portable Solar Powered 220Volts 50Hz pedestrian signals, A 120 or 240 V, 100 amp, single-phase IQUPS.com transfer panel is used to activate the generator at the loss of power. According to IQUPS, the generator assumes the full load in seven seconds. When utility power is restored, the generator shuts off and signal operation is automatically returned to the normal power source. "The IQUPS1800 will completely run the intersection stoplights," said general manager for the DOT. "Other backup systems will put the lights to flashing red. When the generator kicks in on the IQUPS1800, the lights will fully function for 25 to 40 hours, depending on the load at the intersection. When power is restored, the system returns to utility power and the traffic signals do not need to be reset." Battery Backups Prevent Accidents at Critical Traffic Signals Additional Applications Being Taken for More Intersections Keeping Traffic Moving When The Power Goes Out Portable Solar Power 120 Volts 60 Hz or 230 Volts 50Hz, Traffic Portable Solar Power 120 Volts 60 Hz Thanks to new IQTraffiControl.com energy-efficiency technology, different Cities, towns and counties will keep their traffic signals safely operating even if the electricity goes out, and other local governments. Intersections have been converted to new LED signal lights utilizing more efficient, LED (light emitting diode) lamps. The new lamps cut the amount of electricity used by each light from as much as 150 watts to between 10 to 25 watts. Because LEDs use so much less electricity, it is now technically possible to provide battery backup power to alike. We also Have Fuel Cells Traffic Backups.

IQ UPS Traffic Back-up Standby Power Generation. - Battery backup systems for LED traffic Signs -

IQUPS Battery Backups Prevent Accidents at Critical Traffic Signals Increase the public safety and reduced traffic congestion by allowing traffic lights to function even during a power failure. A typical traffic signal intersection experiences eight to ten local power outages annually. With battery backup 3 power, some or all the traffic control signals can continue to operate. This seamless switchover to battery power increases public safety and eliminates the need to dispatch police or other service personnel to direct traffic. If all traffic signals were converted to LEDs, the battery backup system would allow full operation of the traffic signals during a power outage, thus alleviating traffic congestion.

Sample Ready to ship unit

GeneralCommunications Wireless Solutions Provider putting the latest RF and IR technology to work to enhance productivity and increase profits. More than a radio company, GeneralCommunications Point Wireless combines wireless (RF & IR) data transmission with extensive array of sensors and application specific modules suited for a variety of common applications. GeneralCommunications works closely with OEMs in dozens of industries to capitalize on the benefits of wireless technology. All products are general purpose in design and appeal to a broad customer base. Typical deployments include traffic light automation, food safety, energy management, access control, fire safety and trucking. The GeneralCommunications value proposition is based on the ability to engineer application specific solutions ranging from basic telemetry to wireless networking. This value arises from GeneralCommunications application awareness and the command of innovative, high value designs. In addition to application specific solutions, Point Six Wireless also offers a complete line of general purpose products for the transmission of Ethernet, serial, Modbus, Weigand, analog, discrete or sensor based data.

Wireless Solution Provider Sensor with integrated Transmitters Adott offers an expanded line of wireless sensors to measure temperature, relative humidity, pressure, vibration, analog voltage and current, and discrete digital inputs. Each sensor is battery operated and fitted with a microprocessor controlled 418 MHz radio transmitter. Item# Description 48400  Sensor Temperature Wireless Temperature and Unique ID Transmitter. Main Features: Digital temperature measurement 64-Bit Unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal Loop antenna Low Cost.   Sensor Counter/Temperature 418 MHz Digital Counter and Temperature Sensor The Point Sensor Counter/Temperature wireless transmitter is a battery operated digital counter and temperature sensor with a microprocessor controlled 418 MHz. Main Features 32-Bit unique ID with 24-bit Digital Counter, 13-bit Temperature, digital input status Switch for installation and service mode indication Broad operating temperature range Up to 600-foot range Transmission rates from 10 to 240 seconds Up to 100 transmitters can coexist Battery lasts from 5 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID, temperature and counter data Internal Loop antenna 48415 Sensor Analog 5V 418 MHz transmitters with analog input and Unique ID Main Features: Analog input 12-bit Analog to Digital Conversion Transmits Unique ID and analog value Up to 600-foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost 48416 Sensor Analog 10V 418 MHz transmitters with 12-bit analog input/ Unique ID Main Features: Analog input 12-bit Analog to Digital Conversion Transmits Unique ID and analog value Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost 48417 Sensor Analog 20mA 418 MHz transmitters with analog input / Unique ID Main Features: Analog input 12-bit Analog to Digital Conversion Transmits Unique ID and analog value Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost 48413 Sensor Temperature / Humidity Wireless Temperature and Relative Humidity Transmitter Main Features: Measures Temperature and Relative Humidity Up to 600-foot transmission range Transmission rates from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Broad operating temperature range Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost 48409 Sensor Magnetic Door Open/close 418 MHz Transmitter Main Features 32-Bit unique ID with 24-bit Digital Counter, digital input status Switch for installation and service mode indication Up to 600-foot range Transmits immediately on status change Up to 100 transmitters can coexist Battery lasts from 5 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID and counter data Internal Loop antenna Low Cost Light 48403 Sensor Motion 418 MHz Transmitter Main Features Digital motion measurement via internal weighted accelerometer 64-Bit unique ID Up to 600 foot transmission range 30 second transmission interval Patent pending Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost 48418 Sensor Pressure 418 MHz Pressure Transmitter Main Features Digital pressure measurement 64-Bit Unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal Loop antenna Low Cost 48404 Sensor Power Monitor 418 MHz Transmitter Main Features Measures current draw 64-Bit unique ID 12-bit analog to digital conversion Transmits unique ID and analog value Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent pending modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS enclosure Water resistant coating on PCB Internal loop antenna Low cost Discrete input 48401   Sensor Pulse Counter 418 MHz Transmitter Main Features 30-Bit unique ID with 24-bit Digital Counter and radio transmitter Counts up to 60,000 pulses per minute Switch for installation and service mode indication Broad operating temperature range Up to 600-foot range Transmission rates from 10 to 240 seconds Up to 100 transmitters can coexist Battery lasts from 6 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID, and counter data Internal Loop antenna Low Cost 48410 Sensor RF Identification 418 MHz. FCC Certified Radio Transmitter Main Features 64-Bit unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent pending Battery life up to 5 years Very small (1.4” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost 48405 Sensor Vibration 418 MHz Transmitter Main Features Digital broad range vibration measurement via internal accelerometer 64-Bit unique ID Up to 600 foot transmission range 30 second transmission interval Patent pending Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost Fire Extinguisher 48402 Sensor Thermistor 418 MHz Transmitter The Point Sensor Thermistor wireless transmitter is a battery operated 10K thermistor interface with a microprocessor controlled 418 MHz. IR Traffic Counters 48407 Counter IR Beam Traffic Counter Battery powered - up to 2 year operation Local display Integrated 418MHz/433MHz transmitter High Impact ABS Enclosure (1.3" x 2.1" x .6") 48408 Counter Plus IR Beam Traffic Counter Battery powered - up to 2 year operation Local display Integrated 418MHz/433MHz transmitter High Impact ABS Enclosure (1.3" x 2.1" x .6") 48412 Counter LV IR Beam Traffic Counter - reflective Low voltage powered Local display Integrated 418MHz/433MHz transmitter High Impact ABS Sensor Enclosure (1.3" x 2.1" x .6") 48414 Counter MOD IR Beam Traffic Counter - reflective Low voltage powered Local Display Optional Dual Beam Optional plug-in transmitter (418/433/900MHz/2.4Ghz) Accommodates external sensors High Impact ABS Sensor Enclosure (3.3" x 3.3" x 1.25") 48419 Proximity Counter IR Beam Proximity Counter No reflector required Range up to 7 feet/2.3 meters Battery powered - up to 2 year operation Integrated 418MHz/433MHz transmitter High Impact ABS Enclosure (1.3" x 2.1" x .6")   Repeat and Log Data GC Repeater Repeater 418 MHz RF Receiver with 900 MHz or 2.4 GHz RF Transceiver Main Features 418 MHz Receiver range up to 600 feet. Built in 900 MHz. or 2.4 GHz. frequency hopping radio for long-range wireless interface. Transceiver Range Indoor: 600’ to 1300’ (900 MHz); 300’ to 750’ (2.4 GHz). Transceiver Range Outdoor (with dipole): 7mi. (900 MHz); 3mi. (2.4 GHz). Transceiver Range Outdoor (with high gain antenna): >20mi. (900 MHz); >12mi. (2.4 GHz). Supports all Point Sensors and LSX transmitters Low power, 6-24 VDC at 200 milliamp transmitting, 70 milliamp receiving. GC Integrator Logger 48420 GC Integrator Logger RS232 RS422 Integrator Logger 418 MHz. Radio Receiver/Logger and 1-Wire Interface Main Features Radio decoder for Point Six wireless sensors ASCII command support for all 1-Wire™ devices Decodes CRC-16 error encoded radio packets Integrated data logger for up to 20 sensors Programmable serial number filters for 20 sensors Battery backed Real Time Clock Provides Search, Family Search and Conditional Search Block mode commands support all 1-Wire™ device functions Supports Touch Memory File Structure for Dallas Semiconductor iButtons™ Automatic CRC16 for TMEX™ files Automatically provides smart strong-pull-up for 1-wire sensors ESD and over-current Protection on the 1-Wire™ bus ESD and over-current Protection on the RS485 bus RS485 Serial Command Interface, (field selectable) RS232 Serial Command Interface, (field selectable) Optional 900 MHz. or 2.4 GHz. Radio Network Interface, (field installation) Optional 418 MHz. radio receiver for Point Sensors, (field installation) Optional Opto-isolated RS485 Serial Command Interface, (field installation) Optional Ethernet (TCP/IP) Network Interface, (field installation) Readable model#, version# and unique 32-bit serial number Internal antennas for 418 MHz. and 900 MHz. or 2.4 GHz. radios Dimensions 130 x 130 x 75 MM Enclosure range-of material: - 40 �C - + 120 �C Enclosure Temp. range in cont. use: 80 �C     Access Control Portable Card Reader Wireless Portable Proximity/IR Card Reader The Portable Card Reader (PCR) from Point Six Wireless is designed to provide the user with a lightweight, compact and aesthetically pleasing method of reading proximity cards. Wireless Stationary Card Reader Wireless Stationary Proximity/IR Card Reader The Stationary Card Reader (SCR) is designed to be used either mounted to a wall or directly to a door and can be operated from external power or internal batteries. Access Panel Connectivity Products Access Panel Connectivity The Control Panel Transceiver (CPT) is a compact data transceiver perfect for those needing high performance and dependable operation. The Door Interface Module (DIM) plugs directly into the Access Control Panel and produces a Wiegand output identical to that of a wired system.     Receivers and Web Servers GCS Server Input: RS485 Mod Burs Output: RS232 900MHz Ethernet Modem/Cel OPC, DDE drivers Archive Data Control Alarm/Event Utilities Server Rf Receiver with an Integrated Data Server Main Features 900 MHz or 2.4 GHz Receiver Supports Point Sensors, LSX transmitters via Point Repeater Communicates: Ethernet (TCP/IP), Modem, serial port Data Logger – logs periodic snapshots of the current readings & logs events Web Server – Dynamic HTML web page server showing current readings and alarms Event based alarms – callout or email Push connection to other hosts using TCP/IP based on alarms Simple ASCII command/response protocol 100 Sensors (total of 100 I/O points) maximum 8600 Historical Records capacity 1800 Event Logging capacity Two level password security Each I/O configurable to trigger events Periodic callouts with interval times of 1 minute to 7 days   GCT Transmitter 504452 Output: RS232 RS485 ModBus OPC, DDE, Drives Transceivers General Purpose 900 MHz./2.4GHz. Spread Spectrum Frequency Hopping Transceivers Main Features LED power and configuration activity indicator Astron AXH900RP SMA R Reverse Polarity SMA 6.5” Antenna High Impact ABS enclosure Channel Capacity hops through 25 channels, Up to 65,000 NetIDs Serial Data Interface Asynchronous (RS-232) CMOS (TTL) signals, 5V, 3.3V tolerant I/O Data Rate - 9600 or 19200 bps Transport Protocol - Transparent networking Network Topology - Multi-drop Channel Data Rate - 10k or 20k bps respectively (vary with data rate) Transmit Power Output - 100mW Rx Sensitivity: -110 or -107 respectively Range - Indoor: 600’ to 1300’ Outdoor: 7mi. with dipole, >20mi. with high gain antenna Interference Rejection - 70 dB at pager and cellular phone frequencies 504454   GCTZR-MA 900-MHz frequency-hopping RS485 Master/Slave auto-sensing radio interface The TZR-MA uses an embedded 100-milliwatt frequency hopping wireless modem that provides communication between a local RS485 network and a remote network of RS485 connected devices. GCV View Output: RS232 RS485 OPC, DDE, Drives View RF Receiver Main Features High performance 418 MHz receiver Compatible with OneSix DDE Server and OPCServer PointView PC Software included Serial connection directly to a PC Powered by RS232 port or external source ASCII radio packet data output Decodes CRC-16 error encoded radio packets DB-9 connector for RS232 interface Up to 480 ft. range GCH Host Output: RS232 RS485 OPC, DDE, Drives Host Low Cost RS232 or RS422 ASCII output 418 MHz. Receiver Main Features: High performance 418 MHz receiver Serial connection directly to a PC Powered by RS232 port or external source. ASCII radio packet data output. Decodes CRC-16 error encoded radio packets. DB-9 connector for RS232/RS422 interface. 600 ft. maximum range     Receivers View Receiver 418MHz/433MHz receiver RS 232 output ASCI format data 450 feet range Host Receiver 418MHz/433MHz receiver RS 232 output ASCI format data 600 feet range Mesh Repeater 418MHz/433MHz to 900MHz/2.4GHz repeating 900MHz to 900MHz SS FH mesh network repeating Serial outputs Self configuring 2000 feet indoor range per Repeater Manager 900MHz/2.4GHz SS FH transceiver TCP/IP output Optional browser based traffic reports OPC/DDE drivers XML compliant Data archiving 2000 feet indoor range Server 900MHz/2.4GHz SS FH transceiver TCP/IP output Modem output Optional browser based traffic reports OPC/DDE drivers XML compliant Data archiving 2000 feet indoor range

Note: To view the above PDF documents, you will need the free Adobe Acrobat Reader
 

Wireless Sensors, Wireless Receivers, Wireless Sensors, Wireless Receivers, high value wireless solutions for the automation and communications industry!